![]() I hadn’t expected to have to file away material. That really, really didn’t feel “bespoke”. I had to elongate that hole with a 500 grit jewelry file I happen to have on hand. The reason is that the Titanium pin has a “lip” on it (likely manufacturing related) that the plastic pin and the plated pins do not have – and so it wouldn’t fit through. Which, when it arrived, did not physically fit into the hole in the cage it is meant to pass through. I ordered a replacement Titanium pin, 2mm higher. The first pin didn’t fit at all, see Measurements above. I suggested they might want to look into tumble-polishing their device after manufacture.įor the finish: Plan on some sanding. When I gave this feedback to Evotion, they told me that they were surprised that I found their finish too rough. If I didn’t have foreskin, I expect this would be quite unpleasant – but maybe not, I hear that cut men become less sensitive. ![]() Some 600 grit and 2,000 grit smoothed that out enough that it’s comfortable on the skin of the penis. Likewise, the “edges” of the cage, where it fits behind the glans, were too rough for comfort. Even with 600 grit followed by 2,000 grit, it was still far too rough. The finish on the plastic is far too rough to go into the urethra. Good thinking on the need to adjust horrible idea with the plastic. ![]() I had originally ordered a plastic pin, thinking that I wanted to save some money in case I needed to adjust the pin and order a replacement. The cage fit well, the issues with the height of the pin aside. I have also given this sizing feedback to Evotion, and received a somewhat generic reply: ” We will sincerely take your thoughts into consideration.” Also give them your glans height and glans width, measured at the same place as the height. My advice: When you are ordering, specify the height of the PA pin – from the piercing hole to the middle of the urethral opening. Shaft and pin are good, now the tip just has to fit. They’re making me a whole new cage now – fingers crossed. That’s going to be uncomfortable for people with a larger glans. Evotion don’t ask for glans height or glans width, just glans length. That was the right height, and I then discovered that the tip is compressing my glans, which leads to excruciating pain when erect. After some measuring, Evotion made me a pin with 18mm PA height, first as a plastic prototype. Update Mar 2020: That pin doesn’t stay comfortable for more than two days, its middle is about at the bottom of the urethral opening, which means there’s another 3mm or so “pushing me down”. What I have now fits into the bottom of the urethral opening snugly when I am flaccid, and is somewhat uncomfortable, though not outright painfully so, when erect. This one works better: In hindsight, I should have asked for 4mm higher, for a total of 17mm. I ordered a replacement pin in Titanium, 2mm higher. It had a height (measured to the middle of the pin) of 13mm, which compressed the glans uncomfortably, became outright painful with erections, and trapped my foreskin so it’d pinch and eventually develop an edema. The first pin they sent me, which I ordered in their “foreskin” model, didn’t work at all. ![]() They do ask for “depth”, the horizontal distance – or in the case of the Bijou, for some reason, the slightly slanted horizontal distance. By “height”, I mean the vertical distance between the piercing and the middle of the urethral opening. What Evotion do not ask for is PA height, and that turned out to be an issue. The shorter length avoids pinching against the cock ring I wear at home. The cage is snug, and compresses me noticeably but not painfully when I am erect. Those measurements turned out to be just right. I ordered a cage with a 36mm inner diameter, 40mm long. Flaccid, I am between 34mm and 40mm wide, and between 53mm and 73mm long. MeasuringĮvotion have a helpful measurement page.After asking for guidance from them, I erred on the smaller side for the shaft diameter and cage length. What I settled on was the 3D-printed Evotion Bijou. I was looking for something that was light-weight, allowed full erections, anchored by the PA, allowed some access for teasing, fit well, and wouldn’t break the bank. I asked Bear to be allowed to wear a cage when I realize I can’t control myself, or for extended travel, and he said he was fine by it. Sometimes, even with years of conditioning behind me, I will stroke myself when not allowed. We have never used a cock cage around here.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |